Update readmes

* EUI-64
* First Endpoint (00 is ZigBee Device Object)
* fc00-ffff Manufacturer specific cluster (0xfc00 is used by the dimmer)

DimmerBed/README.md

@@ -1,25 +1,28 @@
 # Dimmer Switch Ruleset for Color Control
 
 This ruleset is a configuration that can change
-color and temperature for a group of lights.
+color and brightness for a group of lights.
 This may be the case in the bedroom.
 
 The on and off buttons work as expected.
 
-Pressing the on button longer cycles temperature, color, and saturisation mode.
-
-Pressing the brightness buttons change the brightness,
-holding the brightness buttons change the temperature, color, and saturisation respectively.
+Pressing the on button longer (check indicator light)
+changes the mode of the brightness buttons:
 
+* Mode 1:
+  * Short Up/Down: brightness
+  * Long Up/Down: color temperature
+* Mode 2:
+  * Short Up/Down: saturisation
+  * Long Up/Down: hue
 
 ## Devices
 
-```sh
-# IDS="s/BASENAME/xxx/g; s/GROUP/xxx/g; s/DIMMER/xxx/g; s/MEMORY/xxx/g"
-```
+Install the memory sensor before proceding.
 
-Install the memory sensor and note its ID before proceding.
-Use the `mem.sensor.json` file, replace the `BASENAME`, and POST it to the /api/KEY/sensors URL.
+```sh
+IDS="s/BASENAME/xxx/g; s/GROUP/xxx/g; s/DIMMER/xxx/g; s/MEMORY/xxx/g"
+```
 
 * `BASENAME` Basename of the ruleset
 * `GROUP` ID of the group to handle

DimmerBed/mem.sensor.json

@@ -4,5 +4,5 @@
 	"modelid": "MEM001",
 	"manufacturername": "Adrium",
 	"swversion": "1.0",
-	"uniqueid": "00:ad:10:f3:2a:9b-03"
+	"uniqueid": "2b:41:4b:48:75:44:69:XX-01-fd00"
 }

DimmerLiving/README.md

@@ -16,7 +16,7 @@ holding the brightness buttons change the color temperature.
 ## Devices
 
 ```sh
-# IDS="s/BASENAME/xxx/g; s/GROUP1/xxx/g; s/GROUP2/xxx/g; s/DIMMER/xxx/g"
+IDS="s/BASENAME/xxx/g; s/GROUP1/xxx/g; s/GROUP2/xxx/g; s/DIMMER/xxx/g"
 ```
 
 * `BASENAME` Basename of the ruleset

MotionIntelligent/README.md

@@ -12,6 +12,8 @@ It does not switch off the lights, if they were not switched on by the sensor.
 
 ## Devices
 
+Install the memory sensor before proceding.
+
 ```sh
 IDS="s/BASENAME/xxx/g; s/GROUP/xxx/g; s/MOTION/xxx/g; s/AMBIENT/xxx/g; s/MEMORY/xxx/g"
 ```

MotionIntelligent/mem.sensor.json

@@ -4,5 +4,5 @@
 	"modelid": "MEM001",
 	"manufacturername": "Adrium",
 	"swversion": "1.0",
-	"uniqueid": "00:ad:10:f3:2a:9b-02"
+	"uniqueid": "2b:41:4b:48:75:4d:6f:XX-01-fd00"
 }

README.md

@@ -8,16 +8,80 @@ See the readme inside the folder.
 
 ## Installation
 
-The IDs of the components should be replaced first.
-Then the JSON files are submitted by POST to the bridge.
+The JSON files are raw Hue API requests for maximum flexibility and portability.
+Identifiers for lights and sensors are parameterized using uppercase letters.
+Hence, before submitting the configuration files to the bridge,
+they should be replaced as described below.
 
-This can be done using the following snippet:
+Some rulesets also require memory sensors.
+The `BASENAME` and `MAC` parameters should be different for
+every configuration.
+
+### Example
+
+The following snippets demonstrate the installation of the
+[DimmerBed](DimmerBed) ruleset for two different rooms.
+
+First, install the memory sensors and note the returned IDs:
 
 ```sh
-BRIDGE="192.168.0.150"
-APIKEY="1234"
-IDS="s/BASENAME/xxx/g; s/GROUP/xxx/g; s/MOTION/xxx/g; ..."
+PREFIX="http://192.168.0.150/api/1234"
 
-for f in *.rule.json; do cat "$f" | sed "$IDS" | curl "http://$BRIDGE/api/$APIKEY/rules" -H 'Content-Type: application/json' -d @-; done
+IDS="s/BASENAME/BedroomAlice/g; s/XX/00/g"
+
+cat DimmerBed/mem.sensor.json | sed "$IDS" | curl "$PREFIX/sensors" -H 'Content-Type: application/json' -d @-
+
+# Returns: [{"success":{"id":"30"}}]
+
+IDS="s/BASENAME/BedroomBob/g; s/XX/01/g"
+
+cat DimmerBed/mem.sensor.json | sed "$IDS" | curl "$PREFIX/sensors" -H 'Content-Type: application/json' -d @-
+
+# Returns: [{"success":{"id":"31"}}]
 ```
 
+Then, the ruleset can be installed:
+
+```sh
+PREFIX="http://192.168.0.150/api/1234"
+
+IDS="s/BASENAME/BedroomAlice/g; s/GROUP/1/g; s/DIMMER/10/g; s/MEMORY/30/g"
+
+for f in DimmerBed/*.rule.json; do cat "$f" | sed "$IDS" | curl "$PREFIX/rules" -H 'Content-Type: application/json' -d @-; done
+
+IDS="s/BASENAME/BedroomBob/g; s/GROUP/2/g; s/DIMMER/11/g; s/MEMORY/31/g"
+
+for f in DimmerBed/*.rule.json; do cat "$f" | sed "$IDS" | curl "$PREFIX/rules" -H 'Content-Type: application/json' -d @-; done
+```
+
+### Advanced Example
+
+Note that the installation always is the same command.
+This example requires `jq` for fully automated installation.
+
+
+```sh
+install_sensor() {
+	cat $1.sensor.json | sed "$IDS" | \
+		curl "$PREFIX/sensors" -H 'Content-Type: application/json' -d @- | \
+		jq -r .[0].success.id
+}
+
+install_ruleset() {
+	for f in $1/*.rule.json; do cat "$f" | sed "$IDS" | curl "$PREFIX/rules" -H 'Content-Type: application/json' -d @-; done
+}
+
+PREFIX="http://192.168.0.150/api/1234"
+
+IDS="s/BASENAME/BedroomAlice/g; s/XX/00/g"
+mem=$(install_sensor DimmerBed/mem)
+
+IDS="s/BASENAME/BedroomAlice/g; s/GROUP/1/g; s/DIMMER/10/g; s/MEMORY/$mem/g"
+install_ruleset DimmerBed
+
+IDS="s/BASENAME/BedroomBob/g; s/XX/01/g"
+mem=$(install_sensor DimmerBed/mem)
+
+IDS="s/BASENAME/BedroomBob/g; s/GROUP/2/g; s/DIMMER/11/g; s/MEMORY/$mem/g"
+install_ruleset DimmerBed
+```